Home » News » Steroid Recipes » How to Make Injectable Winstrol Oil?

How to Make Injectable Winstrol Oil?

Supplies:
1 Gram winstrol
1 20 ml glass vial or larger
1 20 ml sterile glass vial or larger
1 .45 Whatman sterile syringe filter.
2 5 or 10 ml syringes
2 3 ml syringes
3 18 or 20 gauge pins
2 22 gauge pins
17 ml of sesame seed oil
.2 ml of benzyl alcohol
2 ml of guaiacol (super solvent)
Get the materials for your experiment here

This will make 20ml at 50mg/ml.

Tip: Only try to convert winstrol powder 1 gram at a time, it is very easy to ruin it in the conversion

 

Step 1..

Weigh out 1 gram of winstrol powder,

you will need a scale
(Get your Scale here )
use the tare function to take away the

weight of the container that holds your

powder, and weigh it out to 1 gram.

 

Step 2..

Draw out 2 ml of the super solvent, using 1

of the 3 ml syringes.

Step 3..

Place the powder in the open glass vial, then

add the super solvent to the powder in the vial

Step 4..

A:
Place back on rubber stopper, put one of the

20g pins in the stopper. Place the vial in a small

pan, and place on eye of the stove (you can do

this step in the oven, but I have found this

method works better). Cut on heat, heat until

powder disolves into a liquid (the melting point

of winstrol is between 239.8-242 degrees F).

Turn off heat, and let it cool down still in the

pan, until it reaches room temp. again takes

about 15 minutes.

Vial will be VERY HOT, so use an oven mit.

B:
Also heat seseame oil (heat more than 17ml

because you won’t get it all out) it can be

heated on a stove eye, or in the oven, I

heated mine in the oven in a muffin pan,

the oil needs to reach 212 F., to help

sterilize the oil. I put mine in the oven

at 275 F. Just to make sure.

Step 5

Draw out .2 ml of benzyl alcohol, this is 1%

of the final solution. It is very important

that you do not use more than 1% of the

solution with winstrol, or it could crash

when finished.

Step 6

Add BA to the solution in the vial. Shake

very gently.

Step 7a

Draw out the oil with the 10 ml syringe,

(Be sure you have allowed it to cool down

some) add the 15ml of oil to the solution.

Shake very gently again.

**Note – After adding the oil to the solution

the winstrol may begin to clump up back

into a powder, if it does, you just need to

reheat it again like in Step 4a, remember

to let it cool slowly. My powder did this,

and this took care of it.**

Step 7b

Save 2 ml of oil in the syringe, and re-cap

it. You need this later during the sterile

filter process to make sure none of the

winstrol is left in the filter.

Step 8

Place 1 of the 18 guage pins in the steile

unopened vial, and attach the whatman

sterile filter.

Draw out the solution using the other

10ml syringe, attach to the filter, and

slowly press solution into the sterile vial.

Then use the remainding 2ml of oil in

the other syringe, to run through the

filter, to make sure that none of the

winstrol is left in the filter.

Step 9

After filtering, leave the pin in the

sterile vial, remove the filter. Place

the vial in a small pan, and place

on eye of the stove (you can do this

step in the oven, but I have found

this method works better). Cut on

heat, heat solution for about 15 to

20 minutes. Turn off heat, and let

it cool down still in the pan, until it

reaches room temp. again this takes

about 15 minutes.

Finished Product

Below is what your finished product

should look like, it should be a light

gold color. (unless you used Grape

seed oil, then it will have a greenish tint to it)

Comments are closed.